your paddlesports destination

Keel Strips Reviews

See all reviews for KeelEazy

Average Consumer Review:

(5 Consumer Reviews)

Read reviews for the Keel Strips by KeelEazy as submitted by your fellow paddlers. All of the reviews are created and written by paddlers like you, so be sure to submit your own review and be part of the community!

The long-term durability...

The long-term durability of the product still remains to be seen, so I am primarily reviewing the installation process. Some of the negative reviews I've seen in the past claim KeelEazy is little more than duct tape. Not sure what type of duct tape they were using, but the thickness and perceived durability of KeelEazy is exponentially greater than any duct tape I've ever seen. The KeelEazy installation videos on YouTube are painful and woefully inadequate. When they say the most difficult aspect of installation is separating the backing from the strips, they're not kidding. In fact, it's a mess b/c adhesive wants to stick to the backer, not the KeelEazy strip...which makes a huge mess. Another thing that is highly disappointing is severe shrinkage once the heat gun is applied....which creates a huge headache if you're trying bridge 2" to 4" like I did and want a flawless seam. Instead, I was left with a nasty gap. Hope this review helps. After going through the aggravation of install, I would not buy this product again and instead will eventually just replace it with YakGear's new keel protector.

Installed a two inch strip...

Installed a two inch strip onto my new Current Designs Solstice GTS last year. KeelEazy works exactly as advertised. The white has not faded a bit (despite sitting outside keel up in the south Florida sun 24/7), and the strip shows virtually no wear despite my incessant beach landings and dragging ashore. One reviewer seemed completely displeased, but I suspect improper installation was at hand. The surface needs to be perfectly clean and dry. I used acetone to remove all traces of dirt and residual 303. We did a dry fit first, and used masking tape to establish alignment marks down the entire keel line. As I removed the backing and laid the strip down, my buddy applied the heat gun following me to soften the vinyl for perfect adhesion. He pressed down on the strip with his other hand to insure solid contact. Easy peasy, but it did take both of us. Two observations: 1) do not overheat or under heat -- just get the strip pliable; use a commercial heat gun and not your wife's hair dryer; 2) once laid and in firm contact with the hull, do not pull it back up. Trim lastly, and not as you go along. This is particularly true for radial turns. The most difficult part? Getting it started! I swear it took me ten minutes to make the initial separation of backing from the strip. All in all a cheap investment at $4.00 a running foot.

Keeleazy installed last...

Keeleazy installed last year meticulously followed all directions. Used once with good results. Pulled boat out this year and all glue has dried up and flaking off. I'd give it less than 1 star if I could. Probably why there is no review section on their website just a bunch of phony testimonials!. Stay away from these "cheap and easy" products and install kevlar strips.

I purchased Keel Easy Keel...

I purchased Keel Easy Keel Strips from The Kayak Academy (the only source that I know of in the US) and installed them on my Warren Light Craft. The strips are 2" wide by 1/32" thick vinyl, self adhesive, and can be bent around curve by warming them with a heat gun. For really sharp bends, it is necessary to cut slits or notches and use something like seam sealer to get the 'puckers' to adhere well to the hull.

These keel strips appear to be very abrasion resistant. I installed the strips on each end (2-3-ft on bow and stern) of my 15.5-ft carbon fiber kayak. I had been super careful of my somewhat delicate boat as it has a foam core and no gel coat, so it dents and abrades quite easily. I now can launch from concrete boat ramps and pull up onto rocky beaches with no damage to my hull. After several months of hard use this summer, the keel strips show little wear, vinyl is tough, but when the strips do wear out they can be easily removed using a heat gun, and new strips installed.

Overall, I am quite please with the Keel Easy Keel Strips and highly recommend them.

Are you getting tired of...

Are you getting tired of repairing chips and scratches on the keel of your kayak? Recently I discovered KeelEazy. In the past I have had fiberglass keel strips installed on my boats that cost me in the neighborhood of $200. KeelEazy comes in a roll, is very light weight, and comes in different colors. The cost to install is less than half what it cost me to have a fiberglass keel strip installed. It is a simple do it yourself project. There is an installation video you can view on Youtube. This product is wonderful. KeelEazy has even come out with a new product called HealEazy. It quickly installs under your heel where it rests on the hull of the kayak and prevents your heel from rubbing a hole in the bottom. Do yourself a favor and check it out at www.keeleazy.com.